Mick Fanning Large PC FCSII
*FCS II fins sold only as add-on to board purchases from this site*
Mick Fanning's large signature FCS II fin for fast powerful surfing.
**Shaper's Note - FCSII fins tend to run small, so Todd recommends sizing up from what you normally ride
• Mick's fin has a dynamic flex pattern offering bursts of speed. Ideal for power surfers who like to snap hard off the top and carve long roundhouse cutbacks, this fin provides maximum drive.
Open face, down-the-line waves, particularly good in point and reef breaks.
Performance boards with deep concaves and moderate-to-extreme rocker.
Please Note: this fin is designed to be used exclusively with the FCS II Fin System, and will not fit in the traditional FCS Dual Plug System.
Versatile RTM construction delivers a consistent feel similar to a traditional fiberglass fin, but with the advantage of reduced weight. The stiff flex pattern extends progressively from the base through to the tip helping the surfer to maintain drive and hold through a turn. PC fins are reliable, very responsive, and can be used in a variety of different conditions.
LARGE (75 - 90+ Kg / 165 - 200+ Lbs)
Base: 4.49" / 114mm
Depth: 4.67" / 119mm
Area: 15.70"² / 10054mm²
Base: 4.35" / 110mm
Depth: 4.5" / 114mm
Area: 14.62"² / 9434mm²
Base: 4.04" / 102.6mm
Depth: 4.2" / 106.6mm
Area: 12.73"² / 8215mm²
FCS II Features
Efficient keyless system for quick fin installation and release.
2. Flush Leading Edge
Recessed leading edge with flush base connection improves water flow.
3. Backward Compatible
Grub screws can be inserted to accept your existing FCS fins.
4. Mechanism: Rotating Barrel
Self lubricating, wear resistant barrel locks the fin into the plug.
5. Mechanism: Titanium Rod
Aerospace grade titanium rod applies lateral pressure to the fin tab.
6. Honeycomb Construction Lightweight composite frame encapsulated by high density foam reduces weight and maintains tail flex.
FCS II Design
The FCS II system has been designed to perform at the highest level by seamlessly connecting 3 essential elements in surfing; the surfer, the surfboard and the fins. When paired with fins from the new FCS II Essential Series, it’s now possible to install and remove your fins in seconds, without the need for any screws or tools.
What you’ll find when you ride the new FCS II system is more speed, more drive, more acceleration, and most importantly more response from your board. This equates to better surfing, and you’ll be in the line up faster.
Our team riders have given the new FCS II system their personal tick of approval, which is validation from the best surfers on the planet.
Will the FCSII mechanism keep working over time?
The FCSII mechanism will continue to work no matter how many times you change your fins. This simple, but well refined mechanism constructed from superior materials ensures operational longevity.
FCS has completed repetition testing (installing then removing a fin from the system) with no retention force lost over 4,000 cycles. Under normal conditions, the FCSII system will outlast the life of the board.
Will fins eject out of the system unintentionally when surfing?
The FCSII system has a high fin retaining force (around 12kg/26Ibs) and fins cannot be removed from the system by placing force on the front or side of the fin (i.e. the direction of forces applied to the fin during surfing). A fin can only be removed from the system by applying an upwards force to the rear of the fin.
Will sun and salt water corrode the FCSII mechanism? And how about if sand enters the plug, will it jam?
The FCSII mechanism has been designed to operate in a highly corrosive environment. All materials used to construct the FCSII plug have been selected for their anti-corrosion properties; including titanium which is an inert material (will not rust). If sand enters the plug, the mechanism will not be restricted and will flush out the sand through the open slot cavities.
Will my old FCS (dual tab) fins work with this system?
Yes, you can use all your existing FCS fins with the FCSII system. The FCSII plugs are backwards compatible - grub screws can be used within the FCSII plugs to secure your existing dual tab FCS fins.
FCS has designed a set of unobtrusive silicone infills to fill the gap created by the old fins in the new system. The infills are made from high quality silicone rubber which will not damage the plugs or fins. They are also extremely durable, light and built to withstand extreme temperature and corrosive conditions. The infills replicate the flush leading edge of the new fin design improving the performance of the old fins.